Untuk para engineer yang baru pegang console XSCF di SUN M5000, berikut how to untuk konfig XSCF & membuat domain. Gunakan kabel console satt pertama kali power on.
1. Membuat User
XSCF> adduser eis-installer
XSCF> setprivileges eis-installer platadm useradm auditadm fieldeng
XSCF> password eis-installer
New XSCF password:
BAD PASSWORD: it is based on a dictionary word
Retype new XSCF password:
2. Melihat User yang ada;
XSCF> showuser -l
3. Settime Zone
XSCF> settimezone -c settz -s Asia/Jakarta
Asia/Jakarta
4.Set IP dscp
XSCF> setdscp
DSCP network [0.0.0.0 ] > 192,.168.224.0
DSCP netmask [255.255.255.0 ] >
XSCF address [192.168.224.1 ] >
Domain #00 address [192.168.224.2 ] >
Domain #01 address [192.168.224.3 ] >
Domain #02 address [192.168.224.4 ] >
Domain #03 address [192.168.224.5 ] >
Commit these changes to the database? [y|n] : y
XSCF> setnetwork xscf#0-lan#0 -m 255.255.255.0 12.15.15.140
XSCF> sethostname xscf#0 myServer-sc0
XSCF> sethostname -d myDomain.com
XSCF> setnameserver 3.61.212.99
XSCF> setroute -c add -n 0.0.0.0 -g 12.15.15.1 xscf#0-lan#0
XSCF> applynetwork
XSCF> setssh -c enable
XSCF> rebootxscf
The XSCF will be reset. Continue? [y|n] :y
execute J00shutdown_start -- complete
login: eis-installer
Password:
Login incorrect
login: eis-installer
Password:
XSCF> version -c xcp
XSCF#0 (Active )
XCP0 (Current): 1101
XCP1 (Reserve): 1101
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00) Assigned n n n Unknown Normal
01-0 00(01) Assigned n n n Unknown Normal
XSCF> showdcl -a
DID LSB XSB Status
00 Powered Off
00 00-0
01 01-0
XSCF> deleteboard -c unassign 01-0
XSB#01-0 will be unassigned from domain immediately. Continue?[y|n] :y
XSCF> showdcl -a
DID LSB XSB Status
00 Powered Off
00 00-0
01 01-0
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00) Assigned n n n Unknown Normal
01-0 SP Unavailable n n n Unknown Normal
XSCF> showdcl -a
DID LSB XSB Status
00 Powered Off
00 00-0
01 01-0
XSCF> setdcl -d 00 -r 01
XSCF> showdcl -a
DID LSB XSB Status
00 Powered Off
00 00-0
XSCF> setdcl -d 01 -a 00=01-0
XSCF> showdcl -a
DID LSB XSB Status
00 Powered Off
00 00-sho
---------------------------
01 Powered Off
00 01-0
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00) Assigned n n n Unknown Normal
01-0 SP Unavailable n n n Unknown Normal
XSCF> addboard -c assign -d 01 01-0
XSB#01-0 will be assigned to DomainID 1. Continue?[y|n] :y
XSCF> showboards -a
XSB DID(LSB) Assignment Pwr Conn Conf Test Fault
---- -------- ----------- ---- ---- ---- ------- --------
00-0 00(00) Assigned n n n Unknown Normal
01-0 01(00) Assigned n n n Unknown Normal
XSCF> setdomainmode -d 0 -m autoboot=off
Diagnostic Level :min -> -
Secure Mode :on -> -
Autoboot :on -> off
CPU Mode :auto -> -
The specified modes will be changed.
Continue? [y|n] :y
configured.
Diagnostic Level :min
Secure Mode :on (host watchdog: available Break-signal:non-receive)
Autoboot :off (autoboot:off)
CPU Mode :auto
XSCF> setdomainmode -d 1 -m autoboot=off
Diagnostic Level :min -> -
Secure Mode :on -> -
Autoboot :on -> off
CPU Mode :auto -> -
The specified modes will be changed.
Continue? [y|n] :y
configured.
Diagnostic Level :min
Secure Mode :on (host watchdog: available Break-signal:non-receive)
Autoboot :off (autoboot:off)
CPU Mode :auto
XSCF> poweron -d 0
DomainIDs to power on:00
Continue? [y|n] :y
00 :Powering on
*Note*
This command only issues the instruction to power-on.
The result of the instruction can be checked by the "showlogs power".
XSCF> console -d 0
Connect to DomainID 0?[y|n] :y
POST Sequence 01 CPU Check
POST Sequence 02 Banner
LSB#00 (XSB#00-0): POST 2.15.0 (2010/10/06 14:23)
POST Sequence 03 Fatal Check
POST Sequence 04 CPU Register
POST Sequence 05 STICK
POST Sequence 06 MMU
POST Sequence 07 Memory Initialize
POST Sequence 08 Memory
0 comments:
Post a Comment